湖南机械式剥漆刀调试

钢的淬火是将钢加热到临界温度Ac3(亚共析钢)或Ac1(过共析钢)以上温度，保温一段时间，使之全部或部分奥氏体化，然后以大于临界冷却速度的冷速快冷到Ms以下(或Ms附近等温)进行马氏体(或贝氏体)转变的热处理工艺。通常也将铝合金、铜合金、钛合金、钢化玻璃等材料的固溶处理或带有快速冷却过程的热处理工艺称为淬火。Quenching of steel is a heat treatment process of heating the steel to a temperature above the critical temperature AC3 (hypoeutectoid steel) or AC1 (hypereutectoid steel), holding it for a period of time, making it fully or partially austenitized, and then rapidly cooling it to below MS (or isothermal near MS) at a cooling rate greater than the critical cooling rate for martensite (or bainite) transformation. Generally, the solution treatment of aluminum alloy, copper alloy, titanium alloy, tempered glass and other materials or the heat treatment process with rapid cooling process is also called quenching.杭州千和剥漆刀是电子刮漆的理想工具。湖南机械式剥漆刀调试

Select a suitable cutter head, install it on the chuck at the front end of the machine, insert a enameled wire in the middle of the cutter head, use a fixed wrench to adjust the chuck head so that the cutter head gently clamps the enameled wire, and then withdraw the enameled wire. After opening the switch, hold the coil part with your hand, and then easily push the enameled wire into the cutter head rotating at high speed until it reaches the preset stripping length. Then carefully withdraw the enameled wire, and the stripping can be completed, If necessary, the diameter of the cutter head can be adjusted by loosening and tightening the chuck to control the ideal paint stripping effect, because when the machine is started and the cutter head rotates at high speed, the insulating paint or oxide of the enameled wire will be cut off, and the surface of the enameled wire after peeling is bright and clean.陕西定制剥漆刀维修价格杭州千和剥漆刀工作快捷。

本实用新型的目的是提供一种电感生产自动剥漆机，解决了现有技术中在电感线圈剥漆时，直接使用三个卡爪剥离，卡爪之间的间距无法调节，导致不能适用于各种型号的线圈，局限性较强，在面对不同型号的线圈时，需要更换不同的夹具，更换时间较长，加工速度降低的问题。The purpose of the utility model is to provide an automatic paint stripping machine for inductor production, which solves the problem that in the prior art, three claws are directly used to strip the paint of an inductor coil, and the spacing between the claws cannot be adjusted, resulting in that it can not be applied to various types of coils, and has strong limitations. When facing different types of coils, it needs to replace different clamps, which takes a long time to replace and reduces the processing speed.

漆包线是电机、电器、家用电器、电子、仪表电磁绕组的基础和关键材料，使用时需要将线头的绝缘层去除。一般通过剥漆刀对漆包线进行剥漆，由于剥漆刀在工作过程中一直处于旋转状态，容易出现晃动现象，可能对漆包线造成过度剥漆或者剥漆不完整的现象。Enameledwireisthefoundationandkeymaterialofelectromagneticwindingsofmotors,electricalappliances,householdappliances,electronicsandinstruments,andtheinsulationlayerofthewireheadneedstoberemovedduringuse.Generally,theenameledwireispeeledbythepaintpeelingknife.Sincethepaintpeelingknifeisalwaysrotatingduringtheworkingprocess,itiseasytoshake,whichmaycauseexcessiveorincompletepaintpeelingontheenameledwire.剥漆刀的薄皮的一致性好。

The enameled wire stripping machine provided by the utility model includes: 1. The accommodation hole at the end of the rotating shaft is a stepped hole, and the shaft end of the stripping knife can penetrate into the second-order hole and abut against the first-order hole. The first-order hole can support the shaft end of the stripping knife, making its cooperation more reliable. 2. The porcelain eye has high hardness and smooth surface. The enameled wire slides smoothly on its surface without damage. 3. The chip removal hole enables the paint to be smoothly discharged from the receiving cavity of the mounting seat.剥漆刀的剥皮均匀性高。浙江巨型剥漆刀批发价

杭州千和剥漆刀性能稳定。湖南机械式剥漆刀调试

本实用新型提供的漆包线剥漆机，1.旋转轴的中心的贯穿孔的设置，使漆包线能够穿过所述贯穿孔，进行连续多段剥漆。2.传动组件的设置为所述旋转轴的贯穿孔预留了足够的剥漆空间。3剥漆刀的轴端通过嵌入旋转轴端部的容纳孔内与所述旋转轴配合连接，能够使连接处配合紧密。The enameled wire stripping machine provided by the utility model comprises: 1. The setting of the through-hole in the center of the rotating shaft enables the enameled wire to pass through the through-hole and strip the paint continuously in multiple sections. 2. The setting of the transmission assembly reserves enough paint stripping space for the through-hole of the rotating shaft. 3 the shaft end of the paint stripping knife is fitted and connected with the rotating shaft by being embedded in the accommodation hole at the end of the rotating shaft, so that the joint can be closely fitted.湖南机械式剥漆刀调试

杭州千和精密机械有限公司致力于机械及行业设备，以科技创新实现高质量管理的追求。公司自创立以来，投身于磁力张力器、伺服张力器，气动剪刀、剥漆刀，线嘴、导针，绕线机治具，是机械及行业设备的主力军。千和精密不断开拓创新，追求出色，以技术为先导，以产品为平台，以应用为重点，以服务为保证，不断为客户创造更高价值，提供更优服务。千和精密始终关注自身，在风云变化的时代，对自身的建设毫不懈怠，高度的专注与执着使千和精密在行业的从容而自信。