江苏美国LECO分析仪供应商

美国LECO力可氧氮氢分析仪ONH836 氧氮氢联测仪系列软件部分

1、用户友好界面的Cornerstone软件

力可**的Cornerstone氧氮氢分析软件采用触摸屏界面使用户可完整的达到分析控制、方法设定、在线诊断、数据报告。Cornerstone氧氮氢分析软件允许用户在单一分析界面中完成日常的所有工作，快速而且简单易用。力可创新的批次和重复样品数据分组功能极大简化了样品结果输出和结果标准偏差的自动计算。减少了繁琐的额外数据处理。

2、软件特点和优势

Cornerstone氧氮氢分析软件分成四个主要部分：分析、诊断、设定、仪器，界面可快速导航和组织。工具条、滑动条和下拉式菜单简化了校正和数据处理的参数设定。分析软件同时包括实时的环境参数的检测，提供完整的系统图表模拟。高级诊断程序包括全数字化的在线操作手册、维护模拟演示、图片说明等提供快速指导。Cornerstone氧氮氢分析软件同时支持***的数据文档格式和可变的报告格式。

用户友好界面的Cornerstone™ 软件。江苏美国LECO分析仪供应商

Method Selection

Two methods are described in this application note; either method can be used to analyze iron, steel, nickel-, and cobalt-base alloys. The Precision Method is recommended for general use and will provide the best precision and accuracy throughout the typical O, N, and H concentrations found in this group of metals; approximate cycle time is 3.5 minutes. The Fast Track method can be used where speed of analysis is a critical component; for example, when molten metal is being sampled and results are required in the shortest possible time. This method will produce suitable results for most samples; approximate cycle time is 2.25 minutes. As noted above, sampling and sample preparation are key elements to accurate O, N, and Hdetermination as well. It is up to the user to determine which method best meets their needs.

山西美国LECO分析仪厂家供应***触摸屏技术，用户友好界面软件进行校正、分析、诊断等。

ONH836系列：氧氮氢分析仪（熔融法）

软件特点和优势

Cornerstone氧氮氢分析软件分成4个主要部分：分析、诊断、设定、仪器，界面可以快速导航和组织。工具条、滑动条和下拉式菜单简化了校正和数据处理的参数设定。分析软件同时包括实时的环境参数的监测，提供完整的系统图表模拟。高级诊断程序包括全数字化的在线操作手册、维护模拟演示、图片说明等提供快速指导。Cornerstone氧氮氢分析软件同时支持***的数据文档格式和可变的报告格式。

Summary

The determination of the amount of oxygen, nitrogen, and hydrogen in iron, steel, nickel-, and cobalt-base alloys represents some of the most important quality metrics for these materials. Oxygen is used to create steel from pig iron by removing excess carbon. Oxygen content must be controlled to limit the amount of carbon monoxide that can be formed during solidification which may cause excessive porosity. Nitrogen is considered both an impurity as well as an important alloying agent. Itcan be present as a nitride or interstitially in its gaseous form. Increased nitrogen content is known to increase yield and tensile strength, thus decreasing ductility and formability. Excessive levels may evolve during solidification thus increasing porosity. High hydrogen content is the primary cause of embrittlement, blistering and flaking due to its high

mobility through the lattice and provides no potential alloying benefits. The ONH836 utilizes a high-power

electrode furnace to quickly and efficiently release the target gases from within the sample, which allows

for a very rapid simultaneous determination of oxygen, nitrogen, and hydrogen.

高级诊断程序包括全数字化的在线操作手册、维护模拟演示、图片说明等提供快速指导。

Oxygen, Nitrogen, and Hydrogen in Refractory Metals

Summary

One of the most critical chemical specifications of titanium alloys is the hydrogen content. Too high of a

hydrogen content can cause hydrides to precipitate, which can lead to embrittlement and subsequent

cracking when the alloy is stressed. Hydrogen pickup typically occurs during downstream processing steps

such as heat treating, pickling, and cleaning.

The LECO ONH836 is a simultaneous oxygen, nitrogen, and hydrogen determinator that utilizes an electrode furnace, inert carrier gas, and both infrared and thermal conductivity detection to meet the analytical needs of the refractory metal industry. 

This application note was written specifically for use with the LECO ONH836 series determinator.

减少了繁琐的额外数据处理。江苏美国LECO分析仪供应商

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Add approximately 0.05 g of *** Graphite Powder to a***Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

Press the Analyze button on the instrument screen,the lower electrode will close and the analysis sequence will start and end automatically.

Repeat steps 3b through 3i a minimum of three times for each calibration/drift standard used.