湖南专业分析仪

Instrument calibration/drift correction.

a. Login a minimum of 3 Standard replicates.

b. Weigh a ~1.000 gram of a calibration/drift standard, enter the mass and standard identification into appropriate replicate fields.

c. Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

d. Place the calibration/drift standard into the open port at the top of the loading head.

e. Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

高级诊断程序包括全数字化的在线操作手册、维护模拟演示、图片说明等提供快速指导。湖南专业分析仪

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Calibrate/drift following the procedure outlined in the operator's instruction manual.

Analyze Samples.

Login Sample with the appropriate number of reps.

Weigh approximately *** grams of appropriately prepared sample into a *** Nickel Capsule, enter mass and sample identification into appropriate rep fields. If applicable, place the nickel capsule in the

appropriate autoloader position.

Repeat steps 3c through 3i for sample analysis.

山东进口分析仪咨询报价双直流风扇保证持续冷却，不受电压波动的影响。

LECO—Your source for total analytical solutions

CS CS 844 and 744 Series: Carbon/Sulfur by Combustion

Carbon and sulfur determination by combustion infrared detection

Quick, accurate, and affordable determination for both production control and research

Calibration, analysis, evaluation, and diagnostic functions accessible via user-friendly brand software

GDS GDS 500A and 850A Atomic Emission Spectrometers

Spectral range from 120 to 800 nm

Continuous profile of concentration/thickness

Large, dynamic range with concentrations from ppm to 100% by weight

Short analysis time (minutes)

氧氮氢分析仪的优点

采用惰气熔融技术，同时测定氧、氮和氢元素含量

新设计封闭气路系统，优化气路循环，使氧氮氢测量更准确

可采用更廉价的氩气作为载气

催化炉温度可调，使氧的测量更加准确

气路系统都采用电磁阀控制，新增分段式漏气检测

水冷样品加样端口，有效隔绝杂质气体侵入

仪器配置和氧、氮、氢测量范围可灵活选择

新设计的高灵敏度红外检测池和热导池，有极低的检出限

分析时间短

脉冲炉功率高达8.5kw，温度3000℃

颗粒状样品无需胶囊包裹，使用经济实惠

化学试剂及管路隐藏在门后（可移除）

强大的分析软件（支持数据和应用报告导出、增加评论区及其他更多功能）。

单点和多点校正（线性回归）

可采用自来水、冷却循环水机或交换机冷却

新设计的产品可用于各类生产控制和实验室。

工具条、滑动条和下拉式菜单简化了校正和数据处理的参数设定。

氧氮氢分析仪的常见故障及解决方法

供电正常、通讯正常，点击确认键后分析仪不工作。这是没有水流，炉子温度太高或仪器通道电压不正常。如没有水流，炉子温度太高这些信息会显示在显示器画面上，但没有信息显示说明这两项正常。接下来检查仪器通道零位电压，如果比±3V高出1V以上，可能是因为气瓶空了，或者是空气进入到分析仪中。检查并更换化学试剂，如果有空气进入热导池里，热导池的电压就会＜-6V，此时打开右面的门，堵住炉子气体进口，10s后，热导池电压值必然升高。经过逐一排查，**终确认碱石棉有问题，更换后仪器正常。 ***红外池的恒温绝热技术消除了外界环境温度的干扰。北京美国LECO分析仪厂家直销

长寿命的红外发射光源和无漂移的电路设计保证检测器的长期稳定性。湖南专业分析仪

Procedure - Solid Samples

Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

Clean the upper and lower electrode manually, or, if applicable, remove the crucible and press the analyze button to clean with the automatic cleaner

Add approximately 0.05 g of *** Graphite Powder to a *** Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and end automatically

湖南专业分析仪