江苏LECO氧氮氢分析仪优惠价格

Oxygen, Nitrogen, and Hydrogen in Refractory Metals

Summary

Oxygen and nitrogen are alloying elements in titanium, and are also classified as alpha stabilizing elements as they promote alpha phase alloys. Interstitial oxygen and nitrogen levels can be used to regulate the tensile strength of the material, but due to its high solubility can cause unwanted surface embrittlement. This phenomenon can be leveraged,however, under controlled processing to create surface films that increase surface hardness and wear properties.

上海禹重给您提供各种氧氮氢分析仪，欢迎来电咨询！江苏LECO氧氮氢分析仪优惠价格

736 Series: Oxygen/Nitrogen by Inert Gas Fusion

The 736 family of Elemental Analyzers is designed for routine measurement of oxygen and nitrogen content of

inorganic materials, ferrous and nonferrous alloys, andrefractory materials using the inert gas fusion technique.

These instruments feature our Cornerstone brand ® software, a custom interface designed specifically for

touch-screen operation. Developed by combining longterm research with customer feedback, this easy-to-use

software gives you complete access to instrument control, analysis settings, diagnostics, reporting, and more—without sacrificing valuable bench space.

山西专业分析仪厂家供应分析软件同时包括实时的环境参数的监测，提供完整的系统图表的模拟。

氧氮氢分析仪的常见故障及解决方法：

氧和氮空白值超过20。这是由于气流小，不能将炉子中的空气驱赶出去。可调节气体流量，调节载气压力在0.2~0.4MPa。接通仪器载气，放一个石墨坩埚在下电极上，打开主电源开关，点击软件上的关炉按钮，关闭炉子并等待10s。调节流量调节器，直到流量计a显示为30L／h，打开炉子。调节调节器直到流量计b显示为50L／h，再次关闭炉子。如果以上设置不稳定，则增加流量至100L／h，反复调节直至仪器稳定。

Procedure – Powder/Chip Samples

Determine the instrument blank.

Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

Clean the upper and lower electrode either manually or remove the crucible and press the analyze button to clean with an automatic cleaner if applicable.

Add approximately 0.05 g of *** Graphite Powder to a 782-720 Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

采用三个**的红外器检测氧含量，同时检测CO和CO2，然后在转化为CO2集中检测。

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Calibrate/drift following the procedure outlined in the operator's instruction manual.

Analyze Samples.

Login Sample with the appropriate number of reps.

Weigh approximately *** grams of appropriately prepared sample into a *** Nickel Capsule, enter mass and sample identification into appropriate rep fields. If applicable, place the nickel capsule in the

appropriate autoloader position.

Repeat steps 3c through 3i for sample analysis.

提供各种无机材料、钢铁、有色金属、硬质合金陶瓷材料中宽范围的氧氮氢同时测定。安徽美国分析仪采购

可选具有压力补偿和温度控制性能的标气检测气路。江苏LECO氧氮氢分析仪优惠价格

氧氮氢分析仪的使用注意事项：

1 、氧氮氢分析仪在初次启用前，应该对连接点、焊点、阀门等进行检漏，以确保空气中的氧不会反渗进入管道及仪器内部，造成测量数值偏高。

2、再次使用仪器前，要进行管道系统净化，将漏入的空气除干净，同时确保连接取样管路时没有漏入空气。

3、样气中氧含量的变化会受管道材质及表面粗糙度影响，因此一般连接管路选用铜管或抛光过的不锈钢管，而不用塑料管、橡胶管等。

4、微量元素分析时，要避免各种管件、阀门、表头等死角对样气造成污染，因此必须尽可能的简化气路系统，连接件死角要小，以防止溶解氧逸出造成污染，使用水封、油封及腊封等设备，才能较好的确保数据的。

江苏LECO氧氮氢分析仪优惠价格